Recommended products (Seguno)

The Phoenix Inverter Smart is an efficient and reliable inverter. Built on our proven and field tested Phoenix inverter platform, it now comes with a new slimmer design and full metal casing. Models are available in 1600VA, 2000VA and 3000VA for 12, 24 or 48V systems. It’s powerful enough to supply most common plug in appliances in your car, boat, caravan or home. A toroidal transformer provides a high peak power surge capacity, stable voltage, frequency and high quality sine-wave. Description nstallation is simpler than ever before with terminals now more accessible for the installer, enabling a more professional finish.  Features of the - Victron SMART Phoenix Inverter 24V 1600VA - 230V Bluetooth built-in: fully configurable with a tablet or smartphone  Low battery voltage alarm  Low battery voltage cut-off and restart levels  Dynamic cut-off: load dependent cut-off level  Output voltage: 210 – 245V  Frequency: 50 Hz or 60 Hz  ECO mode on/off and ECO mode sense level  Alarm relay  Monitoring: In- and output voltage, load and alarms  VE.Direct communication port  The VE.Direct port can be connected to a computer (VE.Direct to USB interface cable needed) to configure and monitor the same parameters.  Proven reliability  The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature.  High start-up power  Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools. ECO mode  When in ECO mode, the inverter will switch to standby when the load decreases below a preset value. Once in standby the inverter will switch on for a short period every 2,5 seconds (adjustable). If the load exceeds the preset level, the inverter will remain on.  Remote on/off  A remote on/off switch or relay contact can be connected to a two pole connector. Alternatively, the H terminal (left) of the two pole connector can be switched to battery plus, or the L terminal (right) of the two pole connector can be switched to battery minus (or the chassis of a vehicle, for example).  To transfer the load to another AC source: the automatic transfer switch  For our low power inverters we recommend our Filax Automatic Transfer Switch. The Filax features a very short switchover time (less than 20 milliseconds) so that computers and other electronic equipment will continue to operate without disruption. Alternatively use a MultiPlus with built-in transfer switch. 

Read more less

This inverters allows you to power domestic equipment - requiring 230V AC - using 'leisure' or 'automotive' batteries rated at 24V DC. Victron Phoenix Inverters are built to last. They feature sophisticated full-bridge and toroidal transformer topology - which is suitable for powering sensitive electronics. They are overload, temperature, and short-circuit protected. Description Manufacturer : Victron Energy Output Wave Form : Pure Sine Wave Voltage (V) : 24 Continuous Power (W) : 1000 Peak Power (W) : 2200 Continuous Output Power (VA) : 1200 Features VE.Direct communication port  The VE.Direct port can be connected to: • A computer (VE.Direct to USB interface cable needed)  • Apple and Android smartphones, tablets, MacBook’s and other devices (VE.Direct Bluetooth Smart dongle needed)  • UK Type Socket Fully configurable:  • Low battery voltage alarm trip and reset levels  • Low battery voltage cut-off and restart levels  • Dynamic cut-off: load dependent cut-off level  • Output voltage 210 - 245V  • Frequency 50 Hz or 60 Hz  • ECO mode on/off and ECO mode sense level  Monitoring:  • In- and output voltage, % load and alarms  Proven reliability  The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature.  High start-up power  Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools.  ECO mode  When in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on.  Remote on/off  A remote on/off switch can be connected to a two pole connector, or between battery plus and the left hand contact of the two pole connector.  LED diagnosis  Please see manual for a description.  To transfer the load to another AC source: the automatic transfer switch For our low power inverters we recommend our Filax Automatic Transfer Switch. The Filax features a very short switchover time (less than 20 milliseconds) so that computers and other electronic equipment will continue to operate without disruption.

Read more less

This inverters allows you to power domestic equipment - requiring 230V AC - using 'leisure' or 'automotive' batteries rated at 24V DC. Victron Phoenix Inverters are built to last. They feature sophisticated full-bridge and toroidal transformer topology - which is suitable for powering sensitive electronics. They are overload, temperature, and short-circuit protected. Description Manufacturer : Victron Energy Output Wave Form : Pure Sine Wave Voltage (V) : 24 Continuous Power (W) : 400 Peak Power (W) : 900 Continuous Output Power (VA) : 500 Features of the - Victron Phoenix Sine Inverter 24V 500VA -230V VE.Direct - UK VE.Direct communication port  The VE.Direct port can be connected to: • A computer (VE.Direct to USB interface cable needed)  • Apple and Android smartphones, tablets, MacBook’s and other devices (VE.Direct Bluetooth Smart dongle needed)  • UK Type Socket Fully configurable:  • Low battery voltage alarm trip and reset levels  • Low battery voltage cut-off and restart levels  • Dynamic cut-off: load dependent cut-off level  • Output voltage 210 - 245V  • Frequency 50 Hz or 60 Hz  • ECO mode on/off and ECO mode sense level  Monitoring:  • In- and output voltage, % load and alarms  Proven reliability  The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature.  High start-up power  Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools.  ECO mode  When in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on.  Remote on/off  A remote on/off switch can be connected to a two pole connector, or between battery plus and the left hand contact of the two pole connector.  LED diagnosis  Please see manual for a description.  To transfer the load to another AC source: the automatic transfer switch For our low power inverters we recommend our Filax Automatic Transfer Switch. The Filax features a very short switchover time (less than 20 milliseconds) so that computers and other electronic equipment will continue to operate without disruption.

Read more less

This inverters allows you to power domestic equipment - requiring 230V AC - using 'leisure' or 'automotive' batteries rated at 24V DC. Victron Phoenix Inverters are built to last. They feature sophisticated full-bridge and toroidal transformer topology - which is suitable for powering sensitive electronics. They are overload, temperature, and short-circuit protected. Description Manufacturer : Victron Energy Output Wave Form : Pure Sine Wave Voltage (V) : 24 Continuous Power (W) : 200 Peak Power (W) : 400 Continuous Output Power (VA) : 250 Features VE.Direct communication port  The VE.Direct port can be connected to: • A computer (VE.Direct to USB interface cable needed)  • Apple and Android smartphones, tablets, MacBook’s and other devices (VE.Direct Bluetooth Smart dongle needed) • UK Type Socket Fully configurable:  • Low battery voltage alarm trip and reset levels  • Low battery voltage cut-off and restart levels  • Dynamic cut-off: load dependent cut-off level  • Output voltage 210 - 245V  • Frequency 50 Hz or 60 Hz  • ECO mode on/off and ECO mode sense level  Monitoring:  • In- and output voltage, % load and alarms  Proven reliability  The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature.  High start-up power  Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools.  ECO mode  When in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on.  Remote on/off  A remote on/off switch can be connected to a two pole connector, or between battery plus and the left hand contact of the two pole connector.  LED diagnosis  Please see manual for a description.  To transfer the load to another AC source: the automatic transfer switch For our low power inverters we recommend our Filax Automatic Transfer Switch. The Filax features a very short switchover time (less than 20 milliseconds) so that computers and other electronic equipment will continue to operate without disruption. Pdf

Read more less

One full rated output and one 4 Amp output. Charge voltage can be precisely adjusted to suit any battery system. The input for the charger is 230V at 50/60HZ. Charge voltage can be measured directly on the battery terminals in order to compensate for voltage loss due to cable resistance. An external sensor allows measuring battery temperature and compensating charge voltage accordingly. Features of the - Victron Skylla-TG 24V/50A (1+1) 120-240V  Perfect chargers for any type of battery  Charge voltage can be precisely adjusted to suit any sealed or unsealed battery system. In particular, sealed maintenance free batteries must be charged correctly in order to ensure a long service life. Overvoltage will result in excessive gassing and venting of a sealed battery. The battery will dry out and fail.  Suitable for AC and DC supply (AC-DC and DC-DC operation)  Except for the 3-phase input models, the chargers also accept a DC supply.  Controlled charging  Every TG Charger has a microprocessor, which accurately controls the charging in three steps. The charging process takes place in accordance with the IUoUo characteristic and charges more rapidly than other processes.  Use of TG Chargers as a power supply  As a result of the perfectly stabilized output voltage, a TG Charger can be used as a power supply if batteries or large buffer capacitors are not available. Two outputs to charge 2 battery banks (24V models only) The TG Chargers feature 2 isolated outputs. The second output, limited to approximately 4A and with a slightly lower output voltage, is intended to top up a starter battery.  To increase battery life: temperature compensation  Every Skylla TG Charger comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed batteries which otherwise might be overcharged and dry out due to venting.  Battery voltage sense  In order to compensate for voltage loss due to cable resistance, TG Chargers are provided with a voltage sense facility so that the battery always receives the correct charge voltage.

Read more less

Adaptive 4-stage charge characteristic: bulk – absorption – float – storage The Phoenix Charger features a microprocessor controlled ‘adaptive’ battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimise the process relative to the way the battery is being used. Adaptive 4-stage charge characteristic: bulk – absorption – float – storage  The Phoenix Charger features a microprocessor controlled ‘adaptive’ battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimise the process relative to the way the battery is being used.  The right amount of charge: variable absorption time  When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged.  Preventing damage due to excessive gassing: the BatterySafe mode (see fig. 2 below)  If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Phoenix Charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached (see the charge curve between 14,4 V and 15,0 V in fig. 2 below).  Less maintenance and aging when the battery is not in use: the Storage mode (see fig. 1 & 2 below)  The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2 V/cell (13,2 V for 12 V battery) to minimize gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.  To increase battery life: temperature compensation  Every Phoenix Charger comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed batteries and/or when important fluctuations of battery temperature are expected.  Battery voltage sense  In order to compensate for voltage loss due to cable resistance, Phoenix Chargers are provided with a voltage sense facility so that the battery always receives the correct charge voltage.  Universal 90-265 V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation)  The chargers will accept a 90-400 V DC supply. Computer interface  Every Phoenix Charger is ready to communicate with a computer through its RS-485 data port. Together with our VEConfigure software, which can be downloaded free of charge from  victronenergy.com and the data link MK3-USB (see accessories), all parameters of the chargers can be customised.  for more info please download this link: Pdf  

Read more less

With boat owners in mind this adaptive 5-step charger can provide 25A of charge. The Phoenix 1+1 model provides 3A to the starter-battery, the rest to the ‘house’ bank. Bluetooth enabled, you can monitor the charger and set alarms straight from your phone. Adaptive, intelligent, dynamic charge features. Features of the - Phoenix Smart IP43 Charger 24V/25A 1+1 outputs 120-240V Bluetooth Smart enabled  Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available.  Phoenix Smart (1+1): two outputs to charge 2 battery banks  The second output, limited to approximately 3A and with a slightly lower output voltage, is intended to top up a starter battery.   Automatic voltage compensation  The charger compensates for voltage drop over the DC cabling by slightly increasing output voltage when the DC current increases. Please see the manual for details.  Adaptive 5-stage charge algorithm: bulk – absorption – recondition – float – storage  The Phoenix Smart Charger features our well-known ‘adaptive’ battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimise the charge process relative to the way the battery is being used.  The right amount of charge: variable absorption time  When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery will be fully charged.  Preventing damage due to excessive gassing: the BatterySafe mode   If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached. Less maintenance and aging when the battery is not in use:  The Storage Mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the Storage Mode float voltage is reduced to 2,2 V/cell (13,2 V for a 12 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.  Also charges Li-ion (LiFePO₄) batteries  Charger on-off control can be implemented by connecting a relay or open collector opto coupler output from a Li-ion BMS to the remote on-off port. Alternatively full control of voltage and current can be achieved with Bluetooth.  Fully programmable charge algorithm  The charge algorithm can be programmed with help of Bluetooth or the VE.Direct interface. Three pre-programmed algorithms can be selected with the mode button (see specifications).  Remote on-off  The remote on/off consists of two terminals: Remote H and Remote L. A remote on/off switch or relay contact can be connected between H and L. Alternatively, terminal H can be pulled high, or terminal L can be pulled low. See manual for details.  VE.Direct interface  For a wired data connection to a Colour Control panel, PC or other devices. Programmable relay  Can be programmed using the VE.Direct interface or a Bluetooth enabled device to trip on an alarm or other events. formore info please download this link>>Pdf

Read more less

With boat owners in mind this adaptive 5-step charger can provide 25A of charge. The Phoenix 1+1 model provides 3A to the starter-battery, the rest to the ‘house’ bank. Bluetooth enabled, you can monitor the charger and set alarms straight from your phone. Adaptive, intelligent, dynamic charge features. Features of the - Phoenix Smart IP43 Charger 24V/25A 1+1 outputs Bluetooth Smart enabled  Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available.  Phoenix Smart (1+1): two outputs to charge 2 battery banks  The second output, limited to approximately 3A and with a slightly lower output voltage, is intended to top up a starter battery.   Automatic voltage compensation  The charger compensates for voltage drop over the DC cabling by slightly increasing output voltage when the DC current increases. Please see the manual for details.  Adaptive 5-stage charge algorithm: bulk – absorption – recondition – float – storage  The Phoenix Smart Charger features our well-known ‘adaptive’ battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimise the charge process relative to the way the battery is being used.  The right amount of charge: variable absorption time  When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery will be fully charged.  Preventing damage due to excessive gassing: the BatterySafe mode   If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached. Less maintenance and aging when the battery is not in use:  The Storage Mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the Storage Mode float voltage is reduced to 2,2 V/cell (13,2 V for a 12 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.  Also charges Li-ion (LiFePO₄) batteries  Charger on-off control can be implemented by connecting a relay or open collector opto coupler output from a Li-ion BMS to the remote on-off port. Alternatively full control of voltage and current can be achieved with Bluetooth.  Fully programmable charge algorithm  The charge algorithm can be programmed with help of Bluetooth or the VE.Direct interface. Three pre-programmed algorithms can be selected with the mode button (see specifications).  Remote on-off  The remote on/off consists of two terminals: Remote H and Remote L. A remote on/off switch or relay contact can be connected between H and L. Alternatively, terminal H can be pulled high, or terminal L can be pulled low. See manual for details.  VE.Direct interface  For a wired data connection to a Colour Control panel, PC or other devices. Programmable relay  Can be programmed using the VE.Direct interface or a Bluetooth enabled device to trip on an alarm or other events. formore info please download this link>>Pdf

Read more less

The stylish blind system from Remis. Remifront / Sides give you privacy, isolation and protection against the build up of heat with simple handling. * For Mercedes Sprinter 2006 - 2018 vehicles that have cab mirror with bent foot mount, and the structurally identical: VW Crafter (built 2006-2018). Please Note: this blind system is not suitable for vehicles with airbags on the A-pillar and above the doors. Brand Remis Application Mercedes Benz  

Read more less

Effective protection against insects. Aluminium coated sunscreen/night screen for blackout facility and privacy. Slim line design needing very little fixing space. Easy to install. Side tracks can be easily cut to suit window height. Measure window cut out + 70mm = external frame. Brand Remis Size 750mm X 800mm Application Universal

Read more less

Effective protection against insects. Aluminium coated sunscreen/night screen for blackout facility and privacy. Slim line design needing very little fixing space. Easy to install. Side tracks can be easily cut to suit window height. Measure window cut out + 70mm = external frame. Brand Remis Size 800mm X 800mm Application Universal

Read more less

Effective protection against insects. Aluminium coated sunscreen/night screen for blackout facility and privacy. Slim line design needing very little fixing space. Easy to install. Side tracks can be easily cut to suit window height. Measure window cut out + 70mm = external frame. Brand Remis Size 900mm X 800mm Application Universal

Read more less