Recommended products (Seguno)

Truma Ultraflow compact housing. The Ultraflow Compact Housing is the standard housing for a pump assembly that does not include a standard accessory point or filtration system. A good start to introducing Ultraflow into your system if you don't already have it. (46030-01). Colour - White. Brand Truma Type Drinking Water Filters

Read more less

The Truma Ultraflow pump assembly is an ergonomic and simple solution to enable you to easily pump water into your vehicle from an external source. It conveniently connects with your Aqua roll or Water hog and is compatible with both the Ultraflow Filter Housing and the Ultraflow Compact Housing. (46040-01). 1.2 bar Brand Truma Type Water Pump Voltage Description 12V DC Length Hose: 800mm Flow Rate Description 9 LPM

Read more less

The Truma Ultraflow inlet hose assembly is used when vehicles have an on-board pump fitted. The assembly has a filter on one end that is submerged in the external water container. (46340-51). Brand Truma Type Water Hose Assemblies

Read more less

Tired of two-ing and fro-ing with your Aquaroll or Waterhog- with the Truma Waterline you don’t have to! This 15 metre hose pipe enables you to link your Ultraflow Water System directly to a mains water supply, providing a constant water flow. Cuts out one of the most physical chores when away in your caravan or motorhome - making life easier. Brand Truma Type Water Hoses

Read more less

The Quattro can be connected to two independent AC sources, for example shore-side power and a generator, or two generators. The Quattro will automatically connect to the active source.  The main output has no-break functionality. In the event of a grid failure, or shore or generator power being disconnected, the Quattro takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, such as air-conditioning or a water heater can be connected to this output. Features of the - Victron Quattro 12V/5000VA 220-100/100A Two AC inputs with integrated transfer switch  The Quattro can be connected to two independent AC sources, for example the public grid and a generator, or two generators. The Quattro will automatically connect to the active source.  Two AC Outputs  The main output has no-break functionality. The Quattro takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, like a water heater for example, can be connected to this output.  Virtually unlimited power thanks to parallel operation  Up to 6 Quattro units can operate in parallel. Six units 48/10000/140, for example, will provide 54kW / 60kVA output power and 840 Amps charging capacity.  Three phase capability  Three units can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected to provide 162kW / 180kVA inverter power and more than 2500A charging capacity.  PowerControl – Dealing with limited generator, shore side or grid power  The Quattro is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (16A per 5kVA Quattro at 230VAC). A current limit can be set on each AC input. The Quattro will then take account of other AC loads and use whatever is spare for charging, thus preventing the generator or mains supply from being overloaded.  PowerAssist – Boosting shore or generator power  This feature takes the principle of PowerControl to a further dimension allowing the Quattro to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the Quattro will make sure that insufficient mains or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.  Solar energy: AC power available even during a grid failure  The Quattro can be used in off grid as well as grid connected PV and other alternative energy systems. Loss of mains detection software is available.  System configuring  In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. - Parallel and three-phase applications can be configured with VE. Bus Quick Configure and VE.Bus System Configuration software. - Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar Chargers can be configured with Assistants (dedicated software for specific applications).  On-site Monitoring and control Several options are available: Battery Monitor, Multi Control Panel, V.E.Net Blue Power panel, Colour Control panel, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).   Remote Monitoring and control  Victron Ethernet Remote, Victron Global Remote and the Colour Control Panel. Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.  Remote configuring  When connected to the Ethernet, systems with a Colour Control panel can be accessed and settings can be changed. Please download this link for more info>>

Read more less

The 3kVA Victron Quattro is a powerful true sine wave inverter, a sophisticated battery charger and a high-speed AC transfer switch in a single compact enclosure. The bigger brother of the Multiplus range, this unit is designed for industrial and commercial systems with multiple AC sources and differential loading, in addition to larger 3-phase systems.  The Quattro can take an inputs from a generator and grid supply. It can be used in conjunction with a battery bank and solar PV inverter as an energy storage system. The unit has two AC outputs, one being programmable to only operate when shore/grid power is available; designed for heavy loads such as washing machines etc. Up to 10 Quattro units can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible. Specifications Features of the - Victron Quattro 12V/3000VA 120-50/50A-230V  Two AC inputs with integrated transfer switch  The Quattro can be connected to two independent AC sources, for example the public grid and a generator, or two generators. The Quattro will automatically connect to the active source.  Two AC Outputs  The main output has no-break functionality. The Quattro takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, like a water heater for example, can be connected to this output.  Virtually unlimited power thanks to parallel operation  Up to 6 Quattro units can operate in parallel. Six units 48/10000/140, for example, will provide 54kW / 60kVA output power and 840 Amps charging capacity.  Three phase capability  Three units can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected to provide 162kW / 180kVA inverter power and more than 2500A charging capacity.  PowerControl – Dealing with limited generator, shore side or grid power  The Quattro is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (16A per 5kVA Quattro at 230VAC). A current limit can be set on each AC input. The Quattro will then take account of other AC loads and use whatever is spare for charging, thus preventing the generator or mains supply from being overloaded.  PowerAssist – Boosting shore or generator power  This feature takes the principle of PowerControl to a further dimension allowing the Quattro to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the Quattro will make sure that insufficient mains or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.  Solar energy: AC power available even during a grid failure  The Quattro can be used in off grid as well as grid connected PV and other alternative energy systems. Loss of mains detection software is available.  System configuring  In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. - Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configuration software. - Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar Chargers can be configured with Assistants (dedicated software for specific applications).  On-site Monitoring and control  Several options are available: Battery Monitor, Multi Control Panel, V.E.Net Blue Power panel, Colour Control panel, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).   Remote Monitoring and control  Victron Ethernet Remote, Victron Global Remote and the Color Control Panel. Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.  Remote configuring  When connected to the Ethernet, systems with a Color Control panel can be accessed and settings can be changed.

Read more less

The MultiPlus, as the name suggests, is a combined inverter and charger in one elegant package. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology, plus multiple system integration features. Specifications Length (mm): 218 Width (mm): 258 Height Inc Terminals (mm): 362 Weight: 18kg Continuous Output Power: 3000 VA - 2400W Peak power: 6000W  Output Wave Form: Pure Sine Wave Voltage (V): 12 Transfer switch (A): 16 AC Input Voltage: 230V Charge Current House Battery (Amps): 120 Charge Starter Battery (Amps): 4 Number of Outputs: 1 Frequency (Hz): 50 Ingress Protection: IP21 Remote Control: Yes UPS: Yes Warranty: 5 Years Features of the - Victron MultiPlus Inverter Charger 12V/3000VA/120-16A - 230V Two AC Outputs - the main output has no break functionality. The MultiPlus takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the battery, like a water heater for example can be connected to this output (second output available on models rated at 3 kVA and more).  Virtually unlimited power thanks to parallel operation - up to 6 Multis can operate in parallel to achieve higher power output. Six 24/5000/120 units, for example, will provide 25 kW / 30 kVA output power with 720 Amps charging capacity.  Three phase capability - in addition to parallel connection, three units of the same model can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected for a huge 75 kW / 90 kVA inverter and more than 2000 Amps charging capacity.  PowerControl - Dealing with limited generator, shore side or grid power - the MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (nearly 10 A per 5 kVA Multi at 230 VAC). With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded.  PowerAssist - Boosting the capacity of shore or generator power - this feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.  Solar energy: AC power available even during a grid failure - the MultiPlus can be used in off grid as well as grid connected PV and other alternative energy systems. Loss of mains detection software is available.  System configuring - in case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. - Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software. - Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar Chargers can be configured with Assistants (dedicated software for specific applications).  On-site Monitoring and control - several options are available: Battery Monitor, Multi Control Panel, Ve.Net Blue Power Panel, Colour Control Panel, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).  Remote Monitoring - and control Victron Ethernet Remote, Victron Global Remote and the Colour Control Panel. Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.   Remote configuring - when connected to the Ethernet, systems with a Colour Control panel can be accessed remotely and settings can be changed. Please download this link and view video below for more info>>Pdf

Read more less

The MultiPlus, as the name suggests, is a combined inverter and charger in one elegant package. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology, plus multiple system integration features. Specifications Length (mm): 218 Width (mm): 258 Height Inc Terminals (mm): 362 Weight: 18kg Continuous Output Power: 3000 VA - 2400W Peak power: 6000W  Output Wave Form: Pure Sine Wave Voltage (V): 12 Transfer switch (A): 16 AC Input Voltage: 230V Charge Current House Battery (Amps): 120 Charge Starter Battery (Amps): 4 Number of Outputs: 1 Frequency (Hz): 50 Ingress Protection: IP21 Remote Control: Yes UPS: Yes Warranty: 5 Years Features of the - Victron MultiPlus Inverter Charger 12V/3000VA/120-16A - 230V Two AC Outputs - the main output has no break functionality. The MultiPlus takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the battery, like a water heater for example can be connected to this output (second output available on models rated at 3 kVA and more).  Virtually unlimited power thanks to parallel operation - up to 6 Multis can operate in parallel to achieve higher power output. Six 24/5000/120 units, for example, will provide 25 kW / 30 kVA output power with 720 Amps charging capacity.  Three phase capability - in addition to parallel connection, three units of the same model can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected for a huge 75 kW / 90 kVA inverter and more than 2000 Amps charging capacity.  PowerControl - Dealing with limited generator, shore side or grid power - the MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (nearly 10 A per 5 kVA Multi at 230 VAC). With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded.  PowerAssist - Boosting the capacity of shore or generator power - this feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.  Solar energy: AC power available even during a grid failure - the MultiPlus can be used in off grid as well as grid connected PV and other alternative energy systems. Loss of mains detection software is available.  System configuring - in case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. - Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software. - Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar Chargers can be configured with Assistants (dedicated software for specific applications).  On-site Monitoring and control - several options are available: Battery Monitor, Multi Control Panel, Ve.Net Blue Power Panel, Colour Control Panel, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).  Remote Monitoring - and control Victron Ethernet Remote, Victron Global Remote and the Colour Control Panel. Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.   Remote configuring - when connected to the Ethernet, systems with a Colour Control panel can be accessed remotely and settings can be changed. Please download this link and view video below for more info>>Pdf

Read more less

The Victron MultiPlus-II is a multifunctional inverter/charger with all the features of the MultiPlus. The MultiPlus-II is ideally suited for professional marine, yachting, vehicle and land based off-grid applications. Specifications The MultiPlus-II combines the functions of the MultiPlus and the MultiGrid. It has all the features of the MultiPlus, plus an external current transformer option to implement PowerControl and PowerAssist and to optimize self-consumption with external current sensing (max. 32A). It also has all the features of the MultiGrid with built-in anti-islanding and an increasingly long list of country approvals.  Features of the -  Victron MultiPlus-II 12V/3000VA Inverter/Charger 120-32A - 230V A MultiPlus, plus ESS (Energy Storage System) functionality  The MultiPlus-II is a multifunctional inverter/charger with all the features of the MultiPlus, plus an external current sensor option which extends the PowerControl and PowerAssist function to 50A resp. 100A. The MultiPlus-II is ideally suited for professional marine, yachting, vehicle and land based off-grid applications. It also has built-in anti-islanding functionality, and an increasingly long list of country approvals for ESS application. Several system configurations are possible. For more detailed information see the ESS Design and configuration manual.  PowerControl and PowerAssist - Boosting the capacity of the grid or a generator  A maximum grid or generator current can be set. The MultiPlus-II will then take account of other AC loads and use whatever is extra for battery charging, thus preventing the generator or grid from being overloaded (PowerControl function). PowerAssist takes the principle of PowerControl to a further dimension. Where peak power is so often required only for a limited period, the MultiPlus-II will compensate insufficient generator, shore or grid power with power from the battery. When the load reduces, the spare power is used to recharge the battery.  Solar energy: AC power available even during a grid failure  The MultiPlus-II can be used in off grid as well as grid connected PV and other alternative energy systems. It is compatible with both solar charger controllers and grid-tie inverters.  Two AC Outputs  The main output has no break functionality. The MultiPlus-II takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus-II. Loads that should not discharge the battery, like a water heater for example, can be connected to this output.  Virtually unlimited power thanks to parallel (not for the 8k, 10k and 15k models) and three phase operation  Up to 6 Multis can operate in parallel to achieve higher power output. Six 48/5000/70 units, for example, will provide 25 kW / 30 kVA output power with 420 Amps charging capacity. In addition to parallel connection, three units of the same model can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected for a 75 kW / 90 kVA inverter and more than 1200 Amps charging capacity.  On-site system configuring, monitoring and control  Settings can be changed in a matter of minutes with VEConfigure software (computer or laptop and MK3-USB interface needed). Several monitoring and control options are available: Cerbo GX, Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart dongle), Battery Monitor, Digital Multi Control Panel.  Remote configuring and monitoring  Install a Cerbo GX or other GX product to connect to the internet. Operational data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge. When connected to the internet, systems can be accessed remotely, and settings can be changed. Please download this link and view video below for more info>>Pdf

Read more less

Quick and easy shade and privacy thanks to this blind system with an integrated magnetic catch (slides from left to right). The side windows are completely pre-assembled and are simply secured to the vehicle door frames. All components of the REMIfront cab blinds fit perfectly into the interior design. The blinds do not cover the ventilation openings. Please Note: this blind system is not suitable for vehicles with airbags on the A-pillar and above the doors. Brand Remis Height Description 175mm Width 1070mm Depth 265mm Weight 11kg Application Fiat Country of Origin Germany  

Read more less

Quick and easy shade and privacy thanks to this blind system with an integrated magnetic catch (slides from left to right). The side windows are completely pre-assembled and are simply secured to the vehicle door frames. All components of the REMIfront cab blinds fit perfectly into the interior design. The blinds do not cover the ventilation openings. Please Note: this blind system is not suitable for vehicles with airbags on the A-pillar and above the doors. Brand Remis Height Description 175mm Width 1070mm Depth 265mm Weight 11kg Application Ford Country of Origin Germany  

Read more less

Quick and easy shade and privacy thanks to this blind system with an integrated magnetic catch (slides from left to right). The side windows are completely pre-assembled and are simply secured to the vehicle door frames. All components of the REMIfront cab blinds fit perfectly into the interior design. The blinds do not cover the ventilation openings.  Please Note: this blind system is not suitable for vehicles with airbags on the A-pillar and above the doors. Brand Remis Height Description 175mm Width 1070mm Depth 265mm Weight 11kg Application Volkswagen Country of Origin Germany  

Read more less