The Victron Skylla-I 24V/80A 3-Outputs 230V is a modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air.
A modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air.
The right amount of charge for a lead-acid battery: variable absorption time
BatterySafe mode: preventing damage due to excessive gassing
Storage mode: less maintenance and aging when the battery is not in use
Smaller and lighter compared to similar models
NMEA 2000 Canbus connection
PowerControl: set a maximum shore power
Remote Control
Li-ion (LiFePo4) ready
Features of the - Victron Skylla-I 24V/80A 3-Outputs 230V
Skylla-i (1+1): two outputs to charge 2 battery banks
The Skylla-i (1+1) features 2 isolated outputs. The second output, limited to approximately 4 A and with a slightly lower output voltage, is intended to top up a starter battery.
Rugged
Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions.
Flexible
Next to a CAN bus (NMEA2000) interface, a rotary switch, DIP switches and potentiometers are available to adapt the charge algorithm to a particular battery and its conditions of use.
Important features:
Synchronised parallel operation Several chargers can be synchronised with the CAN bus interface. This is achieved by simply interconnecting the chargers with RJ45 UTP-cables. Please see the manual for details.
The right amount of charge for a lead-acid battery: variable absorption time
When only shallow discharges occur the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged.
Preventing damage due to excessive gassing: the BatterySafe mode
If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Skylla-i will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached.
Less maintenance and aging when the battery is not in use: the Storage mode
The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2 V/cell (26,4 V for 24 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘refresh’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.
To increase battery life: temperature compensation
Every Skylla-i comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed lead-acid batteries and/or when important fluctuations of battery temperature are expected.
Battery voltage sense
In order to compensate for voltage loss due to cable resistance, the Skylla-i is provided with a voltage sense facility so that the battery always receives the correct charge voltage.
Suitable for AC and DC supply (AC-DC and DC-DC operation)
The chargers also accept a DC supply.
Use as a power supply
As a result of the perfectly stabilized output voltage, the Skylla-i can be used as a power supply if batteries or large buffer capacitors are not available.
Li-Ion (LiFePO4) ready
Simple charger on-off control can be implemented by connecting a relay or open collector optocoupler output from a Li-Ion BMS to the remote control port of the charger. Alternatively, complete control of voltage and current can be achieved by connecting to the galvanically isolated CAN bus port.
For more info please download this link>>Pdf
One full rated output and one 4 Amp output. Charge voltage can be precisely adjusted to suit any battery system. The input for the charger is 230V at 50/60HZ. Charge voltage can be measured directly on the battery terminals in order to compensate for voltage loss due to cable resistance. An external sensor allows measuring battery temperature and compensating charge voltage accordingly.
Features of the - Victron Skylla-TG 24V/50A (1+1) 120-240V
Perfect chargers for any type of battery
Charge voltage can be precisely adjusted to suit any sealed or unsealed battery system. In particular, sealed maintenance free batteries must be charged correctly in order to ensure a long service life. Overvoltage will result in excessive gassing and venting of a sealed battery. The battery will dry out and fail.
Suitable for AC and DC supply (AC-DC and DC-DC operation)
Except for the 3-phase input models, the chargers also accept a DC supply.
Controlled charging
Every TG Charger has a microprocessor, which accurately controls the charging in three steps. The charging process takes place in accordance with the IUoUo characteristic and charges more rapidly than other processes.
Use of TG Chargers as a power supply
As a result of the perfectly stabilized output voltage, a TG Charger can be used as a power supply if batteries or large buffer capacitors are not available. Two outputs to charge 2 battery banks (24V models only) The TG Chargers feature 2 isolated outputs. The second output, limited to approximately 4A and with a slightly lower output voltage, is intended to top up a starter battery.
To increase battery life: temperature compensation
Every Skylla TG Charger comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed batteries which otherwise might be overcharged and dry out due to venting.
Battery voltage sense
In order to compensate for voltage loss due to cable resistance, TG Chargers are provided with a voltage sense facility so that the battery always receives the correct charge voltage.
With boat owners in mind this adaptive 5-step charger can provide 25A of charge. The Phoenix 1+1 model provides 3A to the starter-battery, the rest to the ‘house’ bank. Bluetooth enabled, you can monitor the charger and set alarms straight from your phone. Adaptive, intelligent, dynamic charge features.
Features of the - Phoenix Smart IP43 Charger 24V/25A 1+1 outputs 120-240V
Bluetooth Smart enabled
Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available.
Phoenix Smart (1+1): two outputs to charge 2 battery banks
The second output, limited to approximately 3A and with a slightly lower output voltage, is intended to top up a starter battery.
Automatic voltage compensation
The charger compensates for voltage drop over the DC cabling by slightly increasing output voltage when the DC current increases. Please see the manual for details.
Adaptive 5-stage charge algorithm: bulk – absorption – recondition – float – storage
The Phoenix Smart Charger features our well-known ‘adaptive’ battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimise the charge process relative to the way the battery is being used.
The right amount of charge: variable absorption time
When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery will be fully charged.
Preventing damage due to excessive gassing: the BatterySafe mode
If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached.
Less maintenance and aging when the battery is not in use:
The Storage Mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the Storage Mode float voltage is reduced to 2,2 V/cell (13,2 V for a 12 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.
Also charges Li-ion (LiFePO₄) batteries
Charger on-off control can be implemented by connecting a relay or open collector opto coupler output from a Li-ion BMS to the remote on-off port. Alternatively full control of voltage and current can be achieved with Bluetooth.
Fully programmable charge algorithm
The charge algorithm can be programmed with help of Bluetooth or the VE.Direct interface. Three pre-programmed algorithms can be selected with the mode button (see specifications).
Remote on-off
The remote on/off consists of two terminals: Remote H and Remote L. A remote on/off switch or relay contact can be connected between H and L. Alternatively, terminal H can be pulled high, or terminal L can be pulled low. See manual for details.
VE.Direct interface
For a wired data connection to a Colour Control panel, PC or other devices.
Programmable relay
Can be programmed using the VE.Direct interface or a Bluetooth enabled device to trip on an alarm or other events.
formore info please download this link>>Pdf
With boat owners in mind this adaptive 5-step charger can provide 16A of charge. The Phoenix 1+1 model provides 3A to the starter-battery, the rest to the ‘house’ bank. Bluetooth enabled, you can monitor the charger and set alarms straight from your phone. Adaptive, intelligent, dynamic charge features.
Features of the - Phoenix Smart IP43 Charger 24V/16A 1+1 outputs 230V
Bluetooth Smart enabled
Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available.
Phoenix Smart (1+1): two outputs to charge 2 battery banks
The second output, limited to approximately 3A and with a slightly lower output voltage, is intended to top up a starter battery.
Automatic voltage compensation
The charger compensates for voltage drop over the DC cabling by slightly increasing output voltage when the DC current increases. Please see the manual for details.
Adaptive 5-stage charge algorithm: bulk – absorption – recondition – float – storage
The Phoenix Smart Charger features our well-known ‘adaptive’ battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimise the charge process relative to the way the battery is being used.
The right amount of charge: variable absorption time
When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery will be fully charged.
Preventing damage due to excessive gassing: the BatterySafe mode
If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached.
Less maintenance and aging when the battery is not in use:
The Storage Mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the Storage Mode float voltage is reduced to 2,2 V/cell (13,2 V for a 12 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.
Also charges Li-ion (LiFePO₄) batteries
Charger on-off control can be implemented by connecting a relay or open collector opto coupler output from a Li-ion BMS to the remote on-off port. Alternatively, full control of voltage and current can be achieved with Bluetooth.
Fully programmable charge algorithm
The charge algorithm can be programmed with the help of Bluetooth or the VE.Direct interface. Three pre-programmed algorithms can be selected with the mode button (see specifications).
Remote on-off
The remote on/off consists of two terminals: Remote H and Remote L. A remote on/off switch or relay contact can be connected between H and L. Alternatively, terminal H can be pulled high, or terminal L can be pulled low. See the manual for details.
VE.Direct interface
For a wired data connection to a Colour Control panel, PC, or other devices.
Programmable relay
It can be programmed using the VE.Direct interface or a Bluetooth-enabled device to trip on an alarm or other events.
formore info please download this link>>Pdf
Completely encapsulated: waterproof, shockproof and ignition protected. Water, oil or dirt will not damage the Orion IP67 DC-DC Converter. The casing is made of cast aluminium and the electronics are moulded in resin.
For More Information Please Click the Link Below:
Orion DC-DC Converter IP67 24/12V 100A (1200W) Additional Information
Features of the - Victron Orion -Tr 24/48V-8.5A (120W) Isolated DC-DC Converter
Remote on-off
The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual).
Adjustable output voltage: can also be used as a battery charger
For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.
All models are short circuit proof and can be paralleled to increase output current
An unlimited number of units can be connected in parallel.
High temperature protected
The output current will reduce at high ambient temperature.
IP43 protection
When installed with the screw terminals oriented downwards.
Screw terminals
No special tools needed for installation.
Input fuse (not replaceable)
On 12V and 24V input models only
Specifications
Input voltage range (1): 20-35V
Under voltage shut down: 14V
Under voltage restart: 15V
Nominal output voltage: 48,2V
Output voltage adjust range: 40-60V
Cont. output current at nominal output voltage and 40°C: 8.5A
Maximum output current (10 s) at nominal output voltage: 15A
Short circuit output current: 25A
Cont. output power at 25°C: 480W
Efficiency: 89%
Off load current: < 120mA
Operating temperature range: -20 to +55°C (derate 3% per °C above 40°C)
DC connection: Screw terminals
Maximum cable cross-section: 16 mm²
Dimensions: 130 x 186 x 70 mm
Weight: 1.6 kg
For more information Please Click The Link Below:
Orion -Tr 24/48V-8.5A (400W) Isolated DC-DC Converter Additional Information
Features of the - Victron Orion-Tr 12/12V-30A Isolated DC-DC Converter
Remote on-off
The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual).
Adjustable output voltage: can also be used as a battery chargerFor example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.
All models are short circuit proof and can be paralleled to increase output currentAn unlimited number of units can be connected in parallel.
IP43 protectionWhen installed with the screw terminals oriented downwards.
Screw terminalsNo special tools needed for installation.
Input fuseOn 12V and 24V input models only.
For more info please download this link>>Pdf
Features of the - Victron Orion-Tr 24/12V-20A (240W) Isolated DC-DC converter
Remote on-off
The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual).
Adjustable output voltage: can also be used as a battery charger
For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.
All models are short circuit proof and can be paralleled to increase output current
An unlimited number of units can be connected in parallel.
High temperature protected
The output current will reduce at high ambient temperature.
IP43 protection
When installed with the screw terminals oriented downwards.
Screw terminals
No special tools are needed for installation.
Input fuse (not replaceable)
On 12V and 24V input models only
Specifications
Input voltage range (1): 16-35V
Under voltage shut down: 14V
Under voltage restart: 15V
Nominal output voltage: 12,2V
Output voltage adjust range: 10-15V
Cont. output current at nominal output voltage and 40°C: 20A
Maximum output current (10 s) at nominal output voltage: 25A
Short circuit output current: 50A
Cont. output power at 25°C: 300W
Efficiency: 88%
Off load current: < 100mA
Operating temperature range: -20 to +55°C (derate 3% per °C above 40°C)
DC connection: Screw terminals
Maximum cable cross-section: 16 mm² AWG6
Dimensions: 130 x 186 x 70 mm (5.1 x 7.3 x 2.8 inch)
For more information Please Click The link Below:
Additional Information
Remote on-off
The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual).
Adjustable output voltage: can also be used as a battery charger
For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.
All models are short circuit proof and can be paralleled to increase output current
An unlimited number of units can be connected in parallel.
High temperature protected
The output current will reduce at high ambient temperature.
IP43 protection
When installed with the screw terminals oriented downwards.
Screw terminals
No special tools needed for installation.
Input fuse (not replaceable)
On 12V and 24V input models only
Specifications
Input voltage range (1): 16-35V
Under voltage shut down: 14V
Under voltage restart: 15V
Nominal output voltage: 12,2V
Output voltage adjust range: 10-15V
Cont. output current at nominal output voltage and 40°C: 20A
Maximum output current (10 s) at nominal output voltage: 25A
Short circuit output current: 50A
Cont. output power at 25°C: 300W
Efficiency: 88%
Off load current: < 100mA
Operating temperature range: -20 to +55°C (derate 3% per °C above 40°C)
DC connection: Screw terminals
Maximum cable cross-section: 16 mm² AWG6
Dimensions H x w x d: 130 x 186 x 70 mm (5.1 x 7.3 x 2.8 inch)
Weight: 1,3 kg (3 lb)
PRODUCT CODE: ORI241224110
For more information please click the link below:
Orion-Tr 24/12V-20A (240W) Isolated DC-DC converter Additional Information
Victron Orion voltage dropper designed to convert an input voltage of 24V DC (in fact anywhere between 18V and 35V DC) into a 12V DC output.
The output voltage of this model can be adjusted between 10 volts and 15 volts DC. This voltage converter is suitable for use on most electrical items on board boats, motorhomes and other automotive applications, including charging a 12V battery on a 24V system.
The converter features a remote on-off connector switch enabling it to be operated with a low power switch or by the engine run/stop switch. It can also be connected in parallel with up to 4 other Orion converters to increase the output current.
These droppers are easy to install with no special tools needed. Victron Energy Orion 24/12-25 DC-DC converters are very efficient, running at 96% efficiency due to the use of active rectification (also known as synchronous rectification).
Remote on-off connector
The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by the engine run/stop switch (see manual).
All models with adjustable output can also be used as a battery charger
For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.
All models with adjustable output can be paralleled to increase output current
Up to five units can be connected in parallel.
Easy to install
Delivery includes four Insulated Fastons Female Crimp 6.3mm (eight Fastons in case of the Orion 24/12-40).
For more information please click the link below:
Additional Information
Features of the - Victron Orion-Tr 48/12V 9A (110W) Isolated DC-DC Converter
Remote on-off
The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual).
Adjustable output voltage: can also be used as a battery charger
For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.
All models are short circuit proof and can be paralleled to increase output current
An unlimited number of units can be connected in parallel.
High temperature protected
The output current will reduce at high ambient temperature.
IP43 protection
When installed with the screw terminals oriented downwards.
Screw terminals
No special tools needed for installation.
Input fuse (not replaceable)
On 12V and 24V input models only
Specifications
Input voltage range (1): 32-70V
Under voltage shut down: 28V
Under voltage restart: 30V
Nominal output voltage: 12,2V
Output voltage adjust range: 12-15V
Cont. output current at nominal output voltage and 40°C: 9A
Maximum output current (10 s) at nominal output voltage: 12.5A
Short circuit output current: 27A
Cont. output power at 25°C: 110W
Efficiency: 87%
Off load current: < 50mA
Operating temperature range: -20 to +55°C (derate 3% per °C above 40°C)
DC connection: Screw terminals
Maximum cable cross-section: 16 mm²
Dimensions hxwxd: 100 x 113 x 47 mm
Weight: 0.42 kg
PRODUCT CODE: ORI481210110
For more information please click the link below:
Additional Information
Features of the - Victron Orion 110/12V 30A (360W) Isolated DC-DC Converter
Remote on-off connector on the high power models.
The remote on-off eliminates the need for a high current switch in the input wiring.
The remote on-off can be operated with a low power switch or by the engine run/stop switch.
All models with adjustable output can also be used as a battery charger.
For example to charge a 12 Volt starter or accessory battery in an otherwise 24 Volt system.
All models with adjustable output can be paralleled to increase output current. Up to five units can be connected in parallel.
Specifications
Voltage: 110V
Cont. output current: 30A
Efficiency: 85%
Bluetooth Enabled: No
Dimensions h-w-d: 82 x 132 x 190 mm
Weight: 1.4 kg
For more Information Please click The Link Below:
Additional Information
