Caravan Motorhome & Boat Kits

The MultiPlus, as the name suggests, is a combined inverter and charger in one elegant package. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology, plus multiple system integration features. Specifications Length (mm): 218 Width (mm): 258 Height Inc Terminals (mm): 362 Weight: 19kg Continuous Output Power: 3000 VA - 2400W Peak power: 6000W  Output Wave Form: Pure Sine Wave Voltage (V): 12 AC Input Voltage: 230V Charge Current House Battery (Amps): 120 Charge Starter Battery (Amps): 4 Number of Outputs: 1 Frequency (Hz): 50 Ingress Protection: IP21 Remote Control: Yes UPS: Yes Warranty: 5 Years Features Two AC Outputs - the main output has no break functionality. The MultiPlus takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the battery, like a water heater for example can be connected to this output (second output available on models rated at 3 kVA and more).  Virtually unlimited power thanks to parallel operation - up to 6 Multis can operate in parallel to achieve higher power output. Six 24/5000/120 units, for example, will provide 25 kW / 30 kVA output power with 720 Amps charging capacity.  Three phase capability - in addition to parallel connection, three units of the same model can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected for a huge 75 kW / 90 kVA inverter and more than 2000 Amps charging capacity.  PowerControl - Dealing with limited generator, shore side or grid power - the MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (nearly 10 A per 5 kVA Multi at 230 VAC). With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded.  PowerAssist - Boosting the capacity of shore or generator power - this feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.  Solar energy: AC power available even during a grid failure - the MultiPlus can be used in off grid as well as grid connected PV and other alternative energy systems. Loss of mains detection software is available.  System configuring - in case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. - Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software. - Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar Chargers can be configured with Assistants (dedicated software for specific applications).  On-site Monitoring and control - several options are available: Battery Monitor, Multi Control Panel, Ve.Net Blue Power Panel, Color Control Panel, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).  Remote Monitoring - and control Victron Ethernet Remote, Victron Global Remote and the Color Control Panel. Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.   Remote configuring - when connected to the Ethernet, systems with a Color Control panel can be accessed remotely and settings can be changed.

Read more less

The 3kW Victron Quattro is a powerful true sine wave inverter, a sophisticated battery charger and a high-speed AC transfer switch in a single compact enclosure. The bigger brother of the Multiplus range, this unit is designed for industrial and commercial systems with multiple AC sources and differential loading, in addition to larger 3-phase systems. The Quattro can take an inputs from a generator and grid supply. It can be used in conjunction with a battery bank and solar PV inverter as an energy storage system. The unit has two AC outputs, one being programmable to only operate when shore/grid power is available; designed for heavy loads such as washing machines etc. Up to 10 Quattro units can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible. Features  Two AC inputs with integrated transfer switch  The Quattro can be connected to two independent AC sources, for example the public grid and a generator, or two generators. The Quattro will automatically connect to the active source.  Two AC Outputs  The main output has no-break functionality. The Quattro takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, like a water heater for example, can be connected to this output.  Virtually unlimited power thanks to parallel operation  Up to 6 Quattro units can operate in parallel. Six units 48/10000/140, for example, will provide 54kW / 60kVA output power and 840 Amps charging capacity.  Three phase capability  Three units can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected to provide 162kW / 180kVA inverter power and more than 2500A charging capacity.  PowerControl – Dealing with limited generator, shore side or grid power  The Quattro is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (16A per 5kVA Quattro at 230VAC). A current limit can be set on each AC input. The Quattro will then take account of other AC loads and use whatever is spare for charging, thus preventing the generator or mains supply from being overloaded.  PowerAssist – Boosting shore or generator power  This feature takes the principle of PowerControl to a further dimension allowing the Quattro to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the Quattro will make sure that insufficient mains or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.  Solar energy: AC power available even during a grid failure  The Quattro can be used in off grid as well as grid connected PV and other alternative energy systems. Loss of mains detection software is available.  System configuring  In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. - Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configuration software. - Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar Chargers can be configured with Assistants (dedicated software for specific applications).  On-site Monitoring and control S Several options are available: Battery Monitor, Multi Control Panel, V.E.Net Blue Power panel, Colour Control panel, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).   Remote Monitoring and control  Victron Ethernet Remote, Victron Global Remote and the Color Control Panel. Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.  Remote configuring  When connected to the Ethernet, systems with a Color Control panel can be accessed and settings can be changed. Please download the link for more info>>

Read more less

The carry case for the IP65 charger is one of those indispensable accessories. It protects your charger from the knocks and bangs of workshop life. It allows tidy storage, too – cables never get tangled …or lost; everything is in one place; and if you use an IP65 charger in your work – it gives a professional appearance. Compartments accommodate the charger, its input/output cables; plus the battery-clamp/eyelet cable options. (Charger and accessories not included) Dimensions  Height (mm)  295  Width (mm) - 350  Depth (mm) - 105

Read more less

The 20A Blue Smart IP22 6-stage battery charger with built-in Bluetooth is a professional quality charger featuring microprocessor controlled ‘adaptive’ charging technology. The battery management software monitors the way the battery is used and automatically optimises the charging process to suit the usage pattern, so maintaining your battery in the best possible condition. This smart, multi-stage charger operates at up to 93% efficiency and generates up to 4x less heat than some other comparable chargers. When the battery is fully charged and has not been used for 24 hours, storage mode kicks in and power consumption drops to less than 0.5W. Cooling is achieved by a near-silent fan and the unit is fully protected against over-temperature, short circuit and reverse polarity.  Built-in Bluetooth allows you to monitor the status of your charger via any Android or Apple device or laptop and all settings of the charger can be configured with the VictronConnect app.  Suitable for all lead acid batteries (particularly leisure or 'deep-cycle' batteries) and Lithium-ion batteries used in caravans, motorhomes, campervans, cars, boats, off-road, industrial and commercial vehicles  Recommended for batteries with a capacity in the range of 75 - 120Ah  Features  6-stage adaptive charging (Test - Bulk - Absorption - Recondition - Float - Storage)  High efficiency and low heat generation  Charges all lead-acid batteries (flooded, AGM, Gel) and Lithium-Ion batteries  NIGHT and LOW setting - reduces to 50% nominal output and no-fan for silent operation Near-silent fan  Over-temperature protection  Short-circuit protection for DC output  Reverse polarity protection for AC input (ATO blade fuse)  Green LED to indicate Power ON  Yellow LED for charge status indication (Bulk-fast blinking / Absorption-slow blinking / Float-solid / Storage-off)  Screw terminals for connection  Can be used as a power supply when no battery is connected  Charger reduces output current at high temp rather than shut-down  Setup, configuration and monitoring by Bluetooth connection  5 year manufacturer's warranty  Specification  Input voltage rating: 180 - 265V AC  Output voltage (Absorption/Float/Storage): 14.2-14.7/13.5-13.8/13.2-13.5 VDC  Max. charge current: 20A  NIGHT or LOW charge current: 10A  No. charging stages: 6 (adaptive)  No. outputs: 1  Minimum battery capacity: 75Ah  'No load' power consumption: 0.5W  Operating temperature: -20ºC to +50ºC (full rated output up to +30ºC, then output reduces)  Cooling method: Fan-assisted  Mains connection: BS1363 UK 3-pin plug on 1.5m cable  Battery connection: Screw clamp terminals for max. 13mm2 cable (note: output cables and connections not included)  Ingress Protection rating: IP22  Body material: Aluminium (blue RAL5012)  Mounting holes: (download Enclosure dimensions below for full details)  Weight: 1.3kg  Overall dimensions: 235 (L) x 108 (W) x 65 (H) mm For more info please download this link>>Pdf

Read more less

The Victron Energy Automotive IP65 Battery Charger 6V/12V-1,1A will automatically adapt its charge algorithm to 6V or 12V batteries making it a very versatile trickle charger for small capacity batteries. DC connector  Depending on the application, clamps, eyelets or a cigarette plug (all included) can be connected to the charger.  Charges 6V and 12V batteries  The charger will automatically adapt its charge algorithm to 6V or 12V batteries Protected against overheating and reverse polarity connection The output current will reduce as temperature increases up to 40°C, but the charger will not fail. Output relay protects against reverse polarity connection. Protected against overheating and reverse polarity connection  The output current will reduce as temperature increases up to 40°C, but the charger will not fail. Output relay protects against reverse polarity connection.  Eight LED’s for status and mode indication  When connected to the AC supply the STAND-BY LED will turn on. No voltage will be present at the output. After connection to a battery (battery voltage must exceed 2V in case of a 6V battery and 7V in case of a 12V battery), charging is initiated by pressing the MODE button. The state of charge of the battery is indicated by 4 LED’s:  1. Red LED marked 25% flashing: state of charge less than 25%.  2. Red LED marked 25% on, and red LED marked 50% flashing: state of charge less than 50%.  3. Red LED’s on, and yellow LED marked 75% flashing: state of charge less than 75%.  4. Red and yellow LED’s on and green LED marked 100% flashing: battery nearly charged.  5. All charge level LED’s solid on: battery fully charged. Flooded, AGM or GEL batteries. Ambient temperature below 10°C, or batteries requiring a higher charge voltage (OPTIMA spiral cell batteries for example).  In case of reverse polarity connection, the orange LED ! will turn on after pressing the MODE button. If the red LED STANDBY remains on, even after pressing the MODE button, the connection to the battery is interrupted. The charger always starts in STANDBY mode when connected to the AC supply.

Read more less

ABS Waterproof IP66 - Cable Entry Cover 

Read more less

Bostik Simson STR 360 Structural adhesive, enables you to fix your solar panel to a variety of surfaces including caravans and motorhomes without the need to drill any holes! STR 360 is a Silyl Modified Polymer (SMP) based adhesive with a high tensile strength and is suitable for making elastic constructive joints. Applications Elastic bondings and sealings in e.g. bus-, caravan- and trailer construction. Bonding of metals, glass and plastics. Features Colour: White Cartridge Size: 290ml Silyl Modified Polymer  Solvent-, isocyanate- and PVC-free. Good UV-resistance and ageing properties. Permanently elastic in a temperature range of –40°C to +90°C In general, STR 360 adheres well without primer on clean, dry, dust- and grease-free substrates of aluminium, stainless steel, galvanised steel, zinc, copper, brass, powder-coated metal, most lacquered metal surfaces, glass, PVC, polyester (GRP), painted and lacquered wood, etc. No adhesion on untreated polyethene, polypropylene and Teflon. In case of high adhesion demands the use of Simson Prep M is recommended. Prep M degreases and prepares the surface of the substrate in one step. On plain, untreated wooden surfaces and other porous substrates, Simson Prep P is recommended. In case the joint is exposed to UV radiation the bond surface has to be protected by UV-blocking methods like Simson Prep G. For more details concerning Prep M, Prep P and Prep G consult the specific technical information data sheets. For not mentioned substrates and additional information consult Bostik. For more info please download the link below Datasheet1

Read more less

Our digital multitester offers 19 testing ranges and 7 functions. The Digital multitester is a really useful tool to have around when installing solar panels as damaged caused by reversed polarity is very common place during setup, it is very easy to check polarity with the multitester eliminating the risk of damage to the solar panel and associated components. Check bulbs, fuses and batteries with ease. Specifications Power Supply: 9Vdc (1 x PP3 supplied) AC voltage: 200 - 500V DC voltage: 200mV - 500V DC current: 5A Resistance: 200Ω - 2000KΩ Test Lead Length: 570mm Dimensions: 126 x70 x 29mm Weight: 128g Features Supplied with shrouded testing probes PVC shockproof jacket PP3 battery included Transistor test function Continuity audible test function Suare wave testing signal output Low battery indication Complies with EN61010 - 1:2010

Read more less

This set of two battery terminals (Positive & Negative) are compatible with Deep Cycling Leisure Batteries. Bolt on battery terminals will give you better connection between your solar panel and the battery enhancing the charging performance. With a choice of 8mm or 10mm diameter posts.

Read more less

S-S type compatible in-line switch. This 200mm extension cable is fitted with S-S type connectors on both ends and a switch in the middle. Ideal for use in solar lighting kits.  Cable Specification 0.75mm max 5A

Read more less

S-S type compatible in-line switch. This 200mm extension cable is fitted with S-S type connectors on both ends and a switch in the middle. Ideal for use in solar lighting kits.  Cable Specification 0.75mm max 5A

Read more less

Here you can purchase custom size 40mm² Flexible DC cable with pre-attached lugs, ideal for linking multiple batteries together.  Our Flexible DC cable is available in six different cable dimensions (mm²) and cable lengths varying from 200mm to 1200mm with a choice of pre-attached lugs. This product is cut and crimped in house so if you have a specific requirement, just ask and we would be more than happy to give you a quote. Heavy Duty 40mm² Flexible Battery Joining Cables custom made with a choice of 8mm or 10mm lugs.

Read more less