Victron Energy Battery Chargers - 12V

The Centaur range of battery chargers features auto-ranging input covering 90-265VAC 50/60Hz input meaning they can be used anywhere in the world. Crucially, and unlike many other products that state universal input, the Centaur range will maintain full output power within the entire specified range. Other features include fully automatic three stage charge characteristic that ensures batteries are fully charged every time and three isolated charge outputs for multi battery configurations to suit the majority of typical installations. The range spans 12V and 24V models from 16A through to 100A. Features of the - Victron Energy Centaur Battery Charger 12V/80A (3) Quality without compromise  Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions.  Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation)  All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz. The chargers also accept a 90-400 V DC supply.  Three outputs that each can supply the full output current  Three isolated outputs to simultaneously charge 3 battery banks Each output is capable to supply the full rated current.  Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries. Recommended battery capacity (Ah): 320 - 800 Dimensions: 505x255x130mm  Weight: 12kg  For more info please download this link>>Pdf

Read more less

The Centaur range of battery chargers features auto-ranging input covering 90-265VAC 50/60Hz input meaning they can be used anywhere in the world. Crucially, and unlike many other products that state universal input, the Centaur range will maintain full output power within the entire specified range. Other features include fully automatic three stage charge characteristic that ensures batteries are fully charged every time and three isolated charge outputs for multi battery configurations to suit the majority of typical installations. The range spans 12V and 24V models from 16A through to 100A. Features of the - Victron Energy Centaur Battery Charger 12V/60A (3) Quality without compromise  Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions.  Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation)  All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz. The chargers also accept a 90-400 V DC supply.  Three outputs that each can supply the full output current  Three isolated outputs to simultaneously charge 3 battery banks Each output is capable to supply the full rated current.  Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries. Recommended battery capacity (Ah): 240 - 600 Dimensions: 426 x 239 x 135mm  Weight: 5kg  For more info please download this link>>Pdf

Read more less

The Centaur range of battery chargers features auto-ranging input covering 90-265VAC 50/60Hz input meaning they can be used anywhere in the world. Crucially, and unlike many other products that state universal input, the Centaur range will maintain full output power within the entire specified range. Other features include fully automatic three stage charge characteristic that ensures batteries are fully charged every time and three isolated charge outputs for multi battery configurations to suit the majority of typical installations. The range spans 12V and 24V models from 16A through to 100A. Features of the - Victron Energy Centaur Battery Charger 12V/50A (3) Quality without compromise  Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions.  Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation)  All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz. The chargers also accept a 90-400 V DC supply.  Three outputs that each can supply the full output current  Three isolated outputs to simultaneously charge 3 battery banks Each output is capable to supply the full rated current.  Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries. Recommended battery capacity (Ah): 200 - 500 Dimensions: 426 x 239 x 135mm  Weight: 5kg  For more info please download this link>>Pdf

Read more less

The Centaur range of battery chargers features auto-ranging input covering 90-265VAC 50/60Hz input meaning they can be used anywhere in the world. Crucially, and unlike many other products that state universal input, the Centaur range will maintain full output power within the entire specified range. Other features include fully automatic three stage charge characteristic that ensures batteries are fully charged every time and three isolated charge outputs for multi battery configurations to suit the majority of typical installations. The range spans 12V and 24V models from 16A through to 100A. The range spans 12V and 24V models from 16A through to 100A. Features of the - Victron Energy Centaur Battery Charger 12V/30A (3) Quality without compromise  Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions.  Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation)  All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz. The chargers also accept a 90-400 V DC supply.  Three outputs that each can supply the full output current  Three isolated outputs to simultaneously charge 3 battery banks Each output is capable to supply the full rated current.  Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries.  Recommended battery capacity (Ah): 120 - 300 Dimensions: 355x215x110mm  Weight: 3.8kg For more info please download this link>>Pdf

Read more less

The Centaur range of battery chargers features auto-ranging input covering 90-265VAC 50/60Hz input meaning they can be used anywhere in the world.  Crucially, and unlike many other products that state universal input, the Centaur range will maintain full output power within the entire specified range. Other features include fully automatic three stage charge characteristic that ensures batteries are fully charged every time and three isolated charge outputs for multi battery configurations to suit the majority of typical installations.  The range spans 12V and 24V models from 16A through to 100A. Features of the - Victron Energy Centaur Battery Charger 12V/30A (3) Quality without compromise  Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions.  Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation)  All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz. The chargers also accept a 90-400 V DC supply.  Three outputs that each can supply the full output current  Three isolated outputs to simultaneously charge 3 battery banks Each output is capable to supply the full rated current.  Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries.  Recommended battery capacity (Ah): 120 - 300 Dimensions: 355x215x110mm  Weight: 3.8kg For more info please download this link>>Pdf

Read more less

The Centaur range of battery chargers features auto-ranging input covering 90-265VAC 50/60Hz input meaning they can be used anywhere in the world.   Crucially, and unlike many other products that state universal input, the Centaur range will maintain full output power within the entire specified range. Other features include fully automatic three stage charge characteristic that ensures batteries are fully charged every time and three isolated charge outputs for multi battery configurations to suit the majority of typical installations.  The range spans 12V and 24V models from 16A through to 100A. Features of the - Victron Energy Centaur Battery Charger 12V/20A (3) Quality without compromise  Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions.  Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation)  All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz. The chargers also accept a 90-400 V DC supply.  Three outputs that each can supply the full output current  Three isolated outputs to simultaneously charge 3 battery banks Each output is capable to supply the full rated current.  Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries.  Recommended battery capacity (Ah): 80 - 200 Dimensions: 355x215x110mm  Weight: 3.8kg For more info please download this link>>Pdf

Read more less

The Victron Energy Automotive IP65 Battery Charger 6V/12V-1,1A will automatically adapt its charge algorithm to 6V or 12V batteries making it a very versatile trickle charger for small capacity batteries. DC connector  Depending on the application, clamps, eyelets or a cigarette plug (all included) can be connected to the charger.  Charges 6V and 12V batteries  The charger will automatically adapt its charge algorithm to 6V or 12V batteries Protected against overheating and reverse polarity connection The output current will reduce as temperature increases up to 40°C, but the charger will not fail. Output relay protects against reverse polarity connection. Protected against overheating and reverse polarity connection  The output current will reduce as temperature increases up to 40°C, but the charger will not fail. Output relay protects against reverse polarity connection.  Eight LED’s for status and mode indication  When connected to the AC supply the STAND-BY LED will turn on. No voltage will be present at the output. After connection to a battery (battery voltage must exceed 2V in case of a 6V battery and 7V in case of a 12V battery), charging is initiated by pressing the MODE button. The state of charge of the battery is indicated by 4 LED’s:  1. Red LED marked 25% flashing: state of charge less than 25%.  2. Red LED marked 25% on, and red LED marked 50% flashing: state of charge less than 50%.  3. Red LED’s on, and yellow LED marked 75% flashing: state of charge less than 75%.  4. Red and yellow LED’s on and green LED marked 100% flashing: battery nearly charged.  5. All charge level LED’s solid on: battery fully charged. Flooded, AGM or GEL batteries. Ambient temperature below 10°C, or batteries requiring a higher charge voltage (OPTIMA spiral cell batteries for example).  In case of reverse polarity connection, the orange LED ! will turn on after pressing the MODE button. If the red LED STANDBY remains on, even after pressing the MODE button, the connection to the battery is interrupted. The charger always starts in STANDBY mode when connected to the AC supply.

Read more less

The 12V/30A Blue Smart IP22 6-stage battery charger with built-in Bluetooth is a professional quality charger featuring microprocessor controlled ‘adaptive’ charging technology. The battery management software monitors the way the battery is used and automatically optimises the charging process to suit the usage pattern, so maintaining your battery in the best possible condition. This model has 3 positive outputs and a common negative output, allowing 3 independent batteries (or banks) to be charged simultaneously. n output reduces)  Cooling method: Fan-assisted   Mains connection: BS1363 UK 3-pin plug on 1.5m cable  Battery connection: Screw clamp terminals for max. 13mm2 cable (note: output cables and connections not included)  Ingress Protection rating: IP22  Body material: Aluminium (blue RAL5012)  Mounting holes: (download Enclosure dimensions below for full details)  Weight: 1.3kg  Overall dimensions: 235 (L) x 108 (W) x 65 (H) mm  For more info please download this link>>Pdf

Read more less

The 30A Blue Smart IP22 6-stage battery charger with built-in Bluetooth is a professional quality charger featuring microprocessor controlled ‘adaptive’ charging technology. The battery management software monitors the way the battery is used and automatically optimises the charging process to suit the usage pattern, so maintaining your battery in the best possible condition. This model has 1 positive output and a UK plug. This smart, multi-stage charger operates at up to 93% efficiency and generates up to 4x less heat than some other comparable chargers. When the battery is fully charged and has not been used for 24 hours, storage mode kicks in and power consumption drops to less than 0.5W. Cooling is achieved by a near-silent fan and the unit is fully protected against over-temperature, short circuit and reverse polarity.  Built-in Bluetooth allows you to monitor the status of your charger via any Android or Apple device or laptop and all settings of the charger can be configured with the VictronConnect app.  Suitable for all lead acid batteries (particularly leisure or 'deep-cycle' batteries) and Lithium-ion batteries used in caravans, motorhomes, campervans, cars, boats, off-road, industrial and commercial vehicles  Recommended for batteries with a capacity in the range of 150 - 250Ah (or up to around 300Ah in total if charging multiple batteries).  Features of the - Blue Smart IP22 Charger 12V/30A - 1 Output - UK Plug 6-stage adaptive charging (Test - Bulk - Absorption - Recondition - Float - Storage)   High efficiency and low heat generation  Charges all lead-acid batteries (flooded, AGM, Gel) and Lithium-Ion batteries  NIGHT and LOW setting - reduces to 50% nominal output and no-fan for silent operation  Near-silent fan  Over-temperature protection  Short-circuit protection for DC output Reverse polarity protection for AC input (ATO blade fuse)  Green LED to indicate Power ON  Yellow LED for charge status indication (Bulk-fast blinking / Absorption-slow blinking / Float-solid / Storage-off)  Screw terminals for connection  Can be used as a power supply when no battery is connected  Charger reduces output current at high temp rather than shut-down  Setup, configuration and monitoring by Bluetooth connection  5 year manufacturer's warranty  Specification  Input voltage rating: 180 - 265V AC  Output voltage (Absorption/Float/Storage): 14.2-14.7/13.5-13.8/13.2-13.5 VDC  Max. charge current: 30A  NIGHT or LOW charge current: 15A  No. charging stages: 6 (adaptive)  'No load' power consumption: 0.5W  Operating temperature: -20ºC to +50ºC (full rated output up to +30ºC, then output reduces)  Cooling method: Fan-assisted   Mains connection: BS1363 UK 3-pin plug on 1.5m cable  Battery connection: Screw clamp terminals for max. 13mm2 cable (note: output cables and connections not included)  Ingress Protection rating: IP22  Body material: Aluminium (blue RAL5012)  Mounting holes: (download Enclosure dimensions below for full details)  Weight: 1.3kg  Overall dimensions: 235 (L) x 108 (W) x 65 (H) mm  For more info please download this link>>Pdf

Read more less

The 20A Blue Smart IP22 6-stage battery charger with built-in Bluetooth is a professional quality charger featuring microprocessor controlled ‘adaptive’ charging technology. The battery management software monitors the way the battery is used and automatically optimises the charging process to suit the usage pattern, so maintaining your battery in the best possible condition. This model has 3 positive outputs and a common negative output, allowing 3 independent batteries (or banks) to be charged simultaneously. This smart, multi-stage charger operates at up to 93% efficiency and generates up to 4x less heat than some other comparable chargers. When the battery is fully charged and has not been used for 24 hours, storage mode kicks in and power consumption drops to less than 0.5W. Cooling is achieved by a near-silent fan and the unit is fully protected against over-temperature, short circuit and reverse polarity.  Built-in Bluetooth allows you to monitor the status of your charger via any Android or Apple device or laptop and all settings of the charger can be configured with the VictronConnect app.  Suitable for all lead acid batteries (particularly leisure or 'deep-cycle' batteries) and Lithium-ion batteries used in caravans, motorhomes, campervans, cars, boats, off-road, industrial and commercial vehicles  Recommended for batteries with a capacity in the range of 75 - 120Ah  Features of the - Blue Smart IP22 Charger 12V/20A - 3 Outputs - UK Plug 6-stage adaptive charging (Test - Bulk - Absorption - Recondition - Float - Storage)  High efficiency and low heat generation  Charges all lead-acid batteries (flooded, AGM, Gel) and Lithium-Ion batteries  NIGHT and LOW setting - reduces to 50% nominal output and no-fan for silent operation Near-silent fan  Over-temperature protection  Short-circuit protection for DC output  Reverse polarity protection for AC input (ATO blade fuse)  Green LED to indicate Power ON  Yellow LED for charge status indication (Bulk-fast blinking / Absorption-slow blinking / Float-solid / Storage-off)  Screw terminals for connection  Can be used as a power supply when no battery is connected  Charger reduces output current at high temp rather than shut-down  Setup, configuration and monitoring by Bluetooth connection  5 year manufacturer's warranty  Specification  Input voltage rating: 180 - 265V AC  Output voltage (Absorption/Float/Storage): 14.2-14.7/13.5-13.8/13.2-13.5 VDC  Max. charge current: 20A  NIGHT or LOW charge current: 10A  No. charging stages: 6 (adaptive)  No. outputs: 1  Minimum battery capacity: 75Ah  'No load' power consumption: 0.5W  Operating temperature: -20ºC to +50ºC (full rated output up to +30ºC, then output reduces)  Cooling method: Fan-assisted  Mains connection: BS1363 UK 3-pin plug on 1.5m cable  Battery connection: Screw clamp terminals for max. 13mm2 cable (note: output cables and connections not included)  Ingress Protection rating: IP22  Body material: Aluminium (blue RAL5012)  Mounting holes: (download Enclosure dimensions below for full details)  Weight: 1.3kg  Overall dimensions: 235 (L) x 108 (W) x 65 (H) mm For more info please download this link>> Pdf

Read more less

The Centaur range of battery chargers features auto-ranging input covering 90-265VAC 50/60Hz input meaning they can be used anywhere in the world.   Crucially, and unlike many other products that state universal input, the Centaur range will maintain full output power within the entire specified range. Other features include fully automatic three stage charge characteristic that ensures batteries are fully charged every time and three isolated charge outputs for multi battery configurations to suit the majority of typical installations.  The range spans 12V and 24V models from 16A through to 100A. Features of the - Victron Energy Centaur Battery Charger 12V/20A (3) Quality without compromise  Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions.  Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation)  All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz. The chargers also accept a 90-400 V DC supply.  Three outputs that each can supply the full output current  Three isolated outputs to simultaneously charge 3 battery banks Each output is capable to supply the full rated current.  Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries.  Recommended battery capacity (Ah): 80 - 200 Dimensions: 355x215x110mm  Weight: 3.8kg For more info please download this link>>Pdf

Read more less

The Blue Smart IP65 Charger 6V/12V 1.1A is the new professional battery charger with built-in bluetooth from Victron. The Blue Smart IP65 Charger can be used on devices in your workshop and on motor vehicles, such as (classic) cars; motorbikes; boats and camper-vans. Specifications The Blue Smart IP65 Charger is the new professional battery charger with built-in Bluetooth. The Blue Smart IP65 Charger can be used on devices in your workshop and on motor vehicles, such as (classic) cars; motorbikes; boats and camper-vans. Features of the - Victron Blue Smart IP65 Battery Charger 6V/12V 1.1A UK The battery is charged, smartly… to perfect condition  The seven-step charging algorithm gets the best out of your battery. The charger gives the battery the power it needs, maintains its health, ensures better performance… and a longer life.  Recovery of deeply-discharged ‘dead’ batteries  Unlike other brands, the Blue Smart IP65 Charger will attempt to recharge a deeply-discharged battery by force-feeding it with a low current. Normal charging will then be resumed as soon as there is sufficient voltage across the battery terminals. Connect the battery with ease  The charger comes with both crocodile clips and M8 eyelets – making it easy to connect to the battery. If you wish, you can leave it permanently connected.  Check the status of your battery remotely  The Blue Smart IP65 is equipped with built-in Bluetooth, so the status of the charger and the battery can be checked on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictronConnect app.  Features  Water, dust and chemical resistant  Seven-step smart charge algorithm  Recovery of fully discharged ‘dead’ batteries  Automatic power supply function  Severe cold performance: down to -30°C  Several other battery life enhancing features  Low power mode to charge smaller batteries  Li-ion battery mode  Setup and configure, readout of voltage and current by Bluetooth Smart  UK type plug

Read more less