Victron Energy Battery Chargers - 12V

LPS II Lithium-Ion Battery Remote Clayton Power   Connection Instructions Remote Control Guide Plug and go - You´ve got the power! Push Button Remote for the 1 and 2 kWh Li-Ion batteries, allowing you to view state of charge, status and active jump start function. Model No. LPS II Remote / RL1802 Width 75 mm Height 50 mm Depth 15 mm Connections 6m Cable

Read more less

With boat owners in mind this adaptive 5-step charger can provide 30A of charge. The Phoenix 1+1 model provides 3A to the starter battery, the rest to the ‘house’ bank. Bluetooth enabled, you can monitor the charger and set alarms straight from your phone. Adaptive, intelligent, dynamic charge features. Features of the - Phoenix Smart IP43 Charger 12V/30A 1+1 outputs Bluetooth Smart enabled  Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available.  Phoenix Smart (1+1): two outputs to charge 2 battery banks  The second output, limited to approximately 3A and with a slightly lower output voltage, is intended to top up a starter battery.   Automatic voltage compensation  The charger compensates for voltage drop over the DC cabling by slightly increasing output voltage when the DC current increases. Please see the manual for details.  Adaptive 5-stage charge algorithm: bulk – absorption – recondition – float – storage  The Phoenix Smart Charger features our well-known ‘adaptive’ battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimise the charge process relative to the way the battery is being used.  The right amount of charge: variable absorption time  When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery will be fully charged.  Preventing damage due to excessive gassing: the BatterySafe mode   If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached. Less maintenance and aging when the battery is not in use:  The Storage Mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the Storage Mode float voltage is reduced to 2,2 V/cell (13,2 V for a 12 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.  Also charges Li-ion (LiFePO₄) batteries  Charger on-off control can be implemented by connecting a relay or open collector opto coupler output from a Li-ion BMS to the remote on-off port. Alternatively, full control of voltage and current can be achieved with Bluetooth.  Fully programmable charge algorithm  The charge algorithm can be programmed with the help of Bluetooth or the VE. Direct interface. Three pre-programmed algorithms can be selected with the mode button (see specifications).  Remote on-off  The remote on/off consists of two terminals: Remote H and Remote L. A remote on/off switch or relay contact can be connected between H and L. Alternatively, terminal H can be pulled high, or terminal L can be pulled low. See the manual for details.  VE.Direct interface  For a wired data connection to a Colour Control panel, PC, or other devices. Programmable relay  Can be programmed using the VE.Direct interface or a Bluetooth-enabled device to trip on an alarm or other events. For more info please download this link>>Pdf

Read more less

The carry case for the IP65 charger is one of those indispensable accessories. It protects your charger from the knocks and bangs of workshop life. It allows tidy storage, too – cables never get tangled …or lost; everything is in one place; and if you use an IP65 charger in your work – it gives a professional appearance. Compartments accommodate the charger, its input/output cables; plus the battery-clamp/eyelet cable options. (Charger and accessories not included) Specifications Smart and professional; this new snap shut carry case provides protective stowage and easy transport for your Blue Smart IP65 charger, and its accessories.  Compartments accommodate the charger, its input/output cables; plus the battery-clamp/eyelet cable options.  Compatible with:   BPC Chargers 12/25 and 24/13 - 345 x 520 x 130mm

Read more less

The carry case for the IP65 charger is one of those indispensable accessories. It protects your charger from the knocks and bangs of workshop life. It allows tidy storage, too – cables never get tangled …or lost; everything is in one place; and if you use an IP65 charger in your work – it gives a professional appearance. Compartments accommodate the charger, its input/output cables; plus the battery-clamp/eyelet cable options. (Charger and accessories not included) Dimensions  Height (mm)  295  Width (mm) - 350  Depth (mm) - 105

Read more less

BPC121542022 - The 15A Blue Smart IP22 6-stage battery charger with built-in Bluetooth is a professional quality charger featuring microprocessor controlled ‘adaptive’ charging technology. The battery management software monitors the way the battery is used and automatically optimises the charging process to suit the usage pattern, so maintaining your battery in the best possible condition. This smart, multi-stage charger operates at up to 93% efficiency and generates up to 4x less heat than some other comparable chargers. When the battery is fully charged and has not been used for 24 hours, storage mode kicks in and power consumption drops to less than 0.5W. Cooling is achieved by a near-silent fan and the unit is fully protected against over-temperature, short circuit and reverse polarity.  Built-in Bluetooth allows you to monitor the status of your charger via any Android or Apple device or laptop and all settings of the charger can be configured with the VictronConnect app.  Suitable for all lead acid batteries (particularly leisure or 'deep-cycle' batteries) and Lithium-ion batteries used in caravans, motorhomes, campervans, cars, boats, off-road, industrial and commercial vehicles  Recommended for batteries with a capacity in the range of 75 - 120Ah  Features of the - Blue Smart IP22 Charger 12V/15A - 1 Output - UK Plug 6-stage adaptive charging (Test - Bulk - Absorption - Recondition - Float - Storage)  High efficiency and low heat generation  Charges all lead-acid batteries (flooded, AGM, Gel) and Lithium-Ion batteries  NIGHT and LOW setting - reduces to 50% nominal output and no-fan for silent operation Near-silent fan  Over-temperature protection  Short-circuit protection for DC output  Reverse polarity protection for AC input (ATO blade fuse)  Green LED to indicate Power ON  Yellow LED for charge status indication (Bulk-fast blinking / Absorption-slow blinking / Float-solid / Storage-off)  Screw terminals for connection  Can be used as a power supply when no battery is connected  Charger reduces output current at high temp rather than shut-down  Setup, configuration and monitoring by Bluetooth connection  5 year manufacturer's warranty  Specification  Input voltage rating: 180 - 265V AC  Output voltage (Absorption/Float/Storage): 14.2-14.7/13.5-13.8/13.2-13.5 VDC  Max. charge current: 15A  NIGHT or LOW charge current: 7.5A  No. charging stages: 6 (adaptive)  No. outputs: 1  Minimum battery capacity: 75Ah  'No load' power consumption: 0.5W  Operating temperature: -20ºC to +50ºC (full rated output up to +30ºC, then output reduces)  Cooling method: Fan-assisted  Mains connection: BS1363 UK 3-pin plug on 1.5m cable  Battery connection: Screw clamp terminals for max. 13mm2 cable (note: output cables and connections not included)  Ingress Protection rating: IP22  Body material: Aluminium (blue RAL5012)  Mounting holes: (download Enclosure dimensions below for full details)  Weight: 1.3kg  Overall dimensions: 235 (L) x 108 (W) x 65 (H) mm For more info please download this link>>Pdf

Read more less

With boat owners in mind, this adaptive 5-step charger can provide 30A of charge. The Phoenix 1+1 model provides 3A to the starter battery, and the rest to the ‘house’ bank. Bluetooth enabled, you can monitor the charger and set alarms straight from your phone. Adaptive, intelligent, dynamic charge features. Features of the - Phoenix Smart IP43 Charger 12V/30A 1+1 outputs Bluetooth Smart enabled  Any Bluetooth enabled smartphone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available.  Phoenix Smart (1+1): two outputs to charge 2 battery banks  The second output, limited to approximately 3A and with a slightly lower output voltage, is intended to top up a starter battery.   Automatic voltage compensation  The charger compensates for voltage drop over the DC cabling by slightly increasing output voltage when the DC current increases. Please see the manual for details.  Adaptive 5-stage charge algorithm: bulk – absorption – recondition – float – storage  The Phoenix Smart Charger features our well-known ‘adaptive’ battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimise the charge process relative to the way the battery is being used.  The right amount of charge: variable absorption time  When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery will be fully charged.  Preventing damage due to excessive gassing: the BatterySafe mode   If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached. Less maintenance and aging when the battery is not in use:  The Storage Mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the Storage Mode float voltage is reduced to 2,2 V/cell (13,2 V for a 12 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.  Also charges Li-ion (LiFePO₄) batteries  Charger on-off control can be implemented by connecting a relay or open collector opto coupler output from a Li-ion BMS to the remote on-off port. Alternatively, full control of voltage and current can be achieved with Bluetooth.  Fully programmable charge algorithm  The charge algorithm can be programmed with the help of Bluetooth or the VE. Direct interface. Three pre-programmed algorithms can be selected with the mode button (see specifications).  Remote on-off  The remote on/off consists of two terminals: Remote H and Remote L. A remote on/off switch or relay contact can be connected between H and L. Alternatively, terminal H can be pulled high, or terminal L can be pulled low. See the manual for details.  VE.Direct interface  For a wired data connection to a Colour Control panel, PC, or other devices. Programmable relay  Can be programmed using the VE.Direct interface or a Bluetooth-enabled device to trip on an alarm or other events. For more info please click this link>>Pdf

Read more less

With boat owners in mind this adaptive 5-step charger can provide 30A of charge. The Phoenix 1+1 model provides 3A to the starter battery, the rest to the ‘house’ bank. Bluetooth enabled, you can monitor the charger and set alarms straight from your phone. Adaptive, intelligent, dynamic charge features. Features of the - Phoenix Smart IP43 Charger 12V/30A 1+1 outputs Bluetooth Smart enabled  Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available.  Phoenix Smart (1+1): two outputs to charge 2 battery banks  The second output, limited to approximately 3A and with a slightly lower output voltage, is intended to top up a starter battery.   Automatic voltage compensation  The charger compensates for voltage drop over the DC cabling by slightly increasing output voltage when the DC current increases. Please see the manual for details.  Adaptive 5-stage charge algorithm: bulk – absorption – recondition – float – storage  The Phoenix Smart Charger features our well-known ‘adaptive’ battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimise the charge process relative to the way the battery is being used.  The right amount of charge: variable absorption time  When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery will be fully charged.  Preventing damage due to excessive gassing: the BatterySafe mode   If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached. Less maintenance and aging when the battery is not in use:  The Storage Mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the Storage Mode float voltage is reduced to 2,2 V/cell (13,2 V for a 12 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.  Also charges Li-ion (LiFePO₄) batteries  Charger on-off control can be implemented by connecting a relay or open collector opto coupler output from a Li-ion BMS to the remote on-off port. Alternatively, full control of voltage and current can be achieved with Bluetooth.  Fully programmable charge algorithm  The charge algorithm can be programmed with the help of Bluetooth or the VE. Direct interface. Three pre-programmed algorithms can be selected with the mode button (see specifications).  Remote on-off  The remote on/off consists of two terminals: Remote H and Remote L. A remote on/off switch or relay contact can be connected between H and L. Alternatively, terminal H can be pulled high, or terminal L can be pulled low. See the manual for details.  VE.Direct interface  For a wired data connection to a Colour Control panel, PC, or other devices. Programmable relay  Can be programmed using the VE.Direct interface or a Bluetooth-enabled device to trip on an alarm or other events. For more info please download this link>>Pdf

Read more less

With boat owners in mind this adaptive 5-step charger can provide 30A of charge. The Phoenix 1+1 model provides 3A to the starter-battery, the rest to the ‘house’ bank. Bluetooth enabled, you can monitor the charger and set alarms straight from your phone. Adaptive, intelligent, dynamic charge features. Features of the - Phoenix Smart IP43 Charger 12V/30A 1+1 outputs 120-240V Bluetooth Smart enabled  Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available.  Phoenix Smart (1+1): two outputs to charge 2 battery banks  The second output, limited to approximately 3A and with a slightly lower output voltage, is intended to top up a starter battery.   Automatic voltage compensation  The charger compensates for voltage drop over the DC cabling by slightly increasing output voltage when the DC current increases. Please see the manual for details.  Adaptive 5-stage charge algorithm: bulk – absorption – recondition – float – storage  The Phoenix Smart Charger features our well-known ‘adaptive’ battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimise the charge process relative to the way the battery is being used.  The right amount of charge: variable absorption time  When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery will be fully charged.  Preventing damage due to excessive gassing: the BatterySafe mode   If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached. Less maintenance and aging when the battery is not in use:  The Storage Mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the Storage Mode float voltage is reduced to 2,2 V/cell (13,2 V for a 12 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.  Also charges Li-ion (LiFePO₄) batteries  Charger on-off control can be implemented by connecting a relay or open collector opto coupler output from a Li-ion BMS to the remote on-off port. Alternatively full control of voltage and current can be achieved with Bluetooth.  Fully programmable charge algorithm  The charge algorithm can be programmed with help of Bluetooth or the VE.Direct interface. Three pre-programmed algorithms can be selected with the mode button (see specifications).  Remote on-off  The remote on/off consists of two terminals: Remote H and Remote L. A remote on/off switch or relay contact can be connected between H and L. Alternatively, terminal H can be pulled high, or terminal L can be pulled low. See manual for details.  VE.Direct interface  For a wired data connection to a Colour Control panel, PC or other devices. Programmable relay  Can be programmed using the VE.Direct interface or a Bluetooth enabled device to trip on an alarm or other events. For more info please download this link>>Pdf

Read more less

With boat owners in mind this adaptive 5-step charger can provide 30A of charge. The Phoenix 1+1 model provides 3A to the starter battery, the rest to the ‘house’ bank. Bluetooth enabled, you can monitor the charger and set alarms straight from your phone. Adaptive, intelligent, dynamic charge features. Features of the - Phoenix Smart IP43 Charger 12V/30A 1+1 outputs Bluetooth Smart enabled  Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available.  Phoenix Smart (1+1): two outputs to charge 2 battery banks  The second output, limited to approximately 3A and with a slightly lower output voltage, is intended to top up a starter battery.   Automatic voltage compensation  The charger compensates for voltage drop over the DC cabling by slightly increasing output voltage when the DC current increases. Please see the manual for details.  Adaptive 5-stage charge algorithm: bulk – absorption – recondition – float – storage  The Phoenix Smart Charger features our well-known ‘adaptive’ battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimise the charge process relative to the way the battery is being used.  The right amount of charge: variable absorption time  When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery will be fully charged.  Preventing damage due to excessive gassing: the BatterySafe mode   If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached. Less maintenance and aging when the battery is not in use:  The Storage Mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the Storage Mode float voltage is reduced to 2,2 V/cell (13,2 V for a 12 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.  Also charges Li-ion (LiFePO₄) batteries  Charger on-off control can be implemented by connecting a relay or open collector opto coupler output from a Li-ion BMS to the remote on-off port. Alternatively, full control of voltage and current can be achieved with Bluetooth.  Fully programmable charge algorithm  The charge algorithm can be programmed with the help of Bluetooth or the VE. Direct interface. Three pre-programmed algorithms can be selected with the mode button (see specifications).  Remote on-off  The remote on/off consists of two terminals: Remote H and Remote L. A remote on/off switch or relay contact can be connected between H and L. Alternatively, terminal H can be pulled high, or terminal L can be pulled low. See the manual for details.  VE.Direct interface  For a wired data connection to a Colour Control panel, PC, or other devices. Programmable relay  Can be programmed using the VE.Direct interface or a Bluetooth-enabled device to trip on an alarm or other events. For more info please download this link>>Pdf

Read more less

Adaptive 4-stage charge characteristic: bulk – absorption – float – storage The Phoenix Charger features a microprocessor controlled ‘adaptive’ battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimise the process relative to the way the battery is being used. Features of the - Victron Energy Centaur Battery Charger 12V/60A (3) Quality without compromise  Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions.  Adaptive 4-stage charge characteristic: bulk – absorption – float – storage  The Phoenix Charger features a microprocessor controlled ‘adaptive’ battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimise the process relative to the way the battery is being used.  The right amount of charge: variable absorption time  When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged.  Preventing damage due to excessive gassing: the BatterySafe mode (see fig. 2 below)  If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Phoenix Charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached (see the charge curve between 14,4 V and 15,0 V in fig. 2 below).  Less maintenance and aging when the battery is not in use: the Storage mode (see fig. 1 & 2 below)  The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2 V/cell (13,2 V for 12 V battery) to minimize gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.  To increase battery life: temperature compensation  Every Phoenix Charger comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed batteries and/or when important fluctuations of battery temperature are expected.  Battery voltage sense  In order to compensate for voltage loss due to cable resistance, Phoenix Chargers are provided with a voltage sense facility so that the battery always receives the correct charge voltage.  Universal 90-265 V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation)  The chargers will accept a 90-400 V DC supply. Computer interface  Every Phoenix Charger is ready to communicate with a computer through its RS-485 data port. Together with our VEConfigure software, which can be downloaded free of charge from  victronenergy.com and the data link MK3-USB (see accessories), all parameters of the chargers can be customised.  For more info please download this link>>Pdf

Read more less

Adaptive 4-stage charge characteristic: bulk – absorption – float – storage The Phoenix Charger features a microprocessor controlled ‘adaptive’ battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimise the process relative to the way the battery is being used. Adaptive 4-stage charge characteristic: bulk – absorption – float – storage  The Phoenix Charger features a microprocessor controlled ‘adaptive’ battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimise the process relative to the way the battery is being used.  The right amount of charge: variable absorption time  When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged.  Preventing damage due to excessive gassing: the BatterySafe mode (see fig. 2 below)  If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Phoenix Charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached (see the charge curve between 14,4 V and 15,0 V in fig. 2 below).  Less maintenance and aging when the battery is not in use: the Storage mode (see fig. 1 & 2 below)  The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2 V/cell (13,2 V for 12 V battery) to minimize gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.  To increase battery life: temperature compensation  Every Phoenix Charger comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed batteries and/or when important fluctuations of battery temperature are expected.  Battery voltage sense  In order to compensate for voltage loss due to cable resistance, Phoenix Chargers are provided with a voltage sense facility so that the battery always receives the correct charge voltage.  Universal 90-265 V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation)  The chargers will accept a 90-400 V DC supply. Computer interface  Every Phoenix Charger is ready to communicate with a computer through its RS-485 data port. Together with our VEConfigure software, which can be downloaded free of charge from  victronenergy.com and the data link MK3-USB (see accessories), all parameters of the chargers can be customised.  For more info please click the link below : Additional Information 

Read more less

The Centaur range of battery chargers features auto-ranging input covering 90-265VAC 50/60Hz input meaning they can be used anywhere in the world. Crucially, and unlike many other products that state universal input, the Centaur range will maintain full output power within the entire specified range. Other features include fully automatic three stage charge characteristic that ensures batteries are fully charged every time and three isolated charge outputs for multi battery configurations to suit the majority of typical installations. The range spans 12V and 24V models from 16A through to 100A. Features of the - Victron Energy Centaur Battery Charger 12V/100A (3) Quality without compromise  Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions.  Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation)  All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz. The chargers also accept a 90-400 V DC supply.  Three outputs that each can supply the full output current  Three isolated outputs to simultaneously charge 3 battery banks Each output is capable to supply the full rated current.  Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries. Recommended battery capacity (Ah): 400 - 1000 Dimensions: 505x255x130mm  Weight: 12kg  For more info please download this link>>Pdf

Read more less